The Bryant Evolution Extreme 26 price varies by unit size, SEER rating, installation complexity, and region; typical installed cost ranges widely. Buyers usually pay between $4,800 and $12,000 total for a complete split-system installation depending on tonnage and required duct or electrical work.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Unit Only (3-ton) | $3,000 | $4,500 | $6,000 | Assumptions: standard coil, mid-SEER model |
| Installed (3-ton) | $4,800 | $7,200 | $10,500 | Assumptions: moderate labor, no major ductwork |
| High-End Install (5-ton, upgrades) | $8,500 | $10,500 | $12,000 | Assumptions: premium controls, long refrigerant lines |
Typical Total Price For Bryant Evolution Extreme 26 Systems
Installed prices for Bryant Evolution Extreme 26 systems depend primarily on tonnage (capacity), SEER/efficiency level, and whether the system replaces existing compatible components. Expect a typical installed range of $4,800-$10,500 for 2.5–5 ton residential systems.
Assumptions: suburban U.S. market, 2.5–3.5 ton common homes, standard 10–15 foot line set, no major duct changes.
Cost Breakdown: Materials, Labor, Equipment, Permits
Major invoice lines separate into equipment, contractor labor, equipment rental, permits, and disposal. Equipment (the outdoor condensing unit and indoor coil/furnace) usually represents 40–60% of the total job price.
| Materials | Labor | Equipment | Permits | Delivery/Disposal |
|---|---|---|---|---|
| $3,000-$6,000 | $1,200-$3,500 | $150-$600 (lift/crane) | $50-$300 | $75-$300 |
Assumptions: labor rate $75-$125 per hour, 6-20 labor hours depending on complexity.
How Unit Size, SEER Rating, And Tonnage Change The Quote
Larger capacity and higher SEER raise the base unit price sharply: 2.5–3 ton units tend to be in the $3,000-$5,000 range while 4–5 ton units are $5,000-$8,000. Moving from a 14–16 SEER model to a 20+ SEER model can add $800-$2,000 or more to equipment cost.
Two numeric thresholds to watch: up-sizing above 3.5 tons typically adds $1,000-$2,000; long refrigerant runs over 50 feet often add $300-$1,000 for extra refrigerant and labor.
Site Conditions That Often Increase Final Price
Tight access, multi-story installs, and long refrigerant/duct runs increase labor and equipment rental. Expect crane or lift fees of $150-$600 when roof access is required.
Other common site thresholds: more than two stories or rooftop installs often push labor up by 30–60%; replacing existing incompatible coil or furnace may add $1,200-$3,000 for matched components and controls.
Practical Ways To Lower Bryant Evolution Extreme 26 Costs
Scope control and timing reduce expense: choose a properly sized unit, avoid unnecessary efficiency upgrades, and schedule in shoulder season. Getting 3-5 written quotes and agreeing to a defined scope can often cut the installed price by 10–20%.
Other tactics: keep existing ducting if in good condition, bundle with furnace replacement for contractor discounts, and prepare the site (clear access, protect flooring) to reduce on-site labor time.
Regional Price Differences And What To Budget By Area
Prices vary by region: coastal and high-cost urban areas run 10–30% higher than Midwest and rural markets. Budget planners: Midwest baseline, add ~15% for East/West coast metro areas and ~25% for high-cost cities.
| Region | Low | Average | High |
|---|---|---|---|
| Midwest | $4,500 | $7,000 | $9,500 |
| Coastal Metro | $5,200 | $8,050 | $11,500 |
| Rural | $4,200 | $6,500 | $9,000 |
Typical Add-Ons, Permits, Timeframe, And Labor Rates
Common extras include new thermostat/controls ($150-$600), refrigerant recharge ($75-$350), and duct sealing ($300-$1,200). Contractor hourly rates typically range $75-$125 per hour; total job time is 6–20 hours depending on scope.
Assumptions: single-family home, 3-ton swap with standard electrical and no major structural work.
Three Real-World Quote Examples With Specs And Totals
Example A: 3-ton, 16 SEER, basic swap: Unit $3,800 + Labor $1,400 + Permits $100 + Disposal $100 = $5,400. Good fit for a 1,600–2,200 sq ft home with existing compatible coil.
Example B: 4-ton, 20 SEER, matched controls, long line set: Unit $6,200 + Labor $2,200 + Crane $350 + Permits $200 = $8,950. Common for larger homes or energy-efficiency upgrades.
Example C: 3.5-ton high-end install with furnace replacement: Unit+furnace $9,000 + Labor $2,800 + Duct sealing $800 + Permits $250 = $12,850. Represents a full system replacement with accessories and HVAC contractor premium.