The Evolution Connex Control price varies widely by model, installation complexity, and whether the unit is used for HVAC, garage/door automation, or industrial access control. Buyers typically pay between $150 and $1,500 total depending on parts, labor, and extra zones or integrations. Assumptions: U.S. retail parts, licensed trade labor, standard single-family home access.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Evolution Connex controller only | $150 | $400 | $900 | Depends on model and integrated I/O |
| Installed in single zone home | $350 | $800 | $1,500 | Includes basic wiring and startup |
| Multi-zone/industrial setup (per zone) | $100 | $300 | $700 | Per additional zone or panel |
How Much the Evolution Connex Controller Itself Costs
Retail price for the Evolution Connex control module alone ranges from $150-$900 depending on model, I/O count, and if it includes a touchscreen or wireless gateway. A basic single-relay model starts near $150 while full-featured models with multiple relays, Ethernet, and advanced firmware hit $700-$900.
Assumptions: new OEM unit, U.S. distributor pricing, excludes tax and shipping.
Breakdown of Typical Quote: Parts, Labor, and Project Fees
Quotes for a standard residential installation usually itemize controller, wiring, conduit, labor, and any permit fees. Expect parts to be 40%-60% of the hardware+materials line and labor to be the remaining primary charge.
| Materials | Labor | Equipment | Permits | Delivery/Disposal |
|---|---|---|---|---|
| $150-$900 (controller, cables, connectors) | $200-$700 (2-6 hours at $75-$125/hr) | $0-$150 (test meters, lifts) | $0-$250 (local electrical/low-voltage) | $0-$75 (old panel disposal) |
How Zone Count and I/O Impact the Final Price
Each additional zone or input/output (I/O) board raises cost by $100-$700 depending on whether the install uses add-on modules or a separate controller. Small installations (1–2 zones) generally add $100-$300 per extra zone; large commercial/integrated sites can add $400-$700 per zone due to custom wiring and testing.
Thresholds: up to 2 zones = minimal add-on; 3–8 zones = modular expansion; 9+ zones = multi-panel or networked controllers.
How Wiring Runs, Conduit, and Mounting Conditions Change Pricing
Long runs, difficult access, or required conduit installation increase labor and materials. Expect $1.50-$4.50 per linear foot for low-voltage cable plus $75-$125 per hour for pull and termination; a 100-foot difficult run can add $200-$600.
Assumptions: standard 18/4 or CAT5/CAT6 cable, normal attic/garage access.
Compatibility, Integration, and Cloud Services That Alter Cost
Integrating the Connex control with HVAC systems, building automation, or cloud monitoring adds hardware and configuration time. Gateway modules or license keys are typically $50-$300; professional cloud setup and mapping can add $150-$500.
Examples: thermostat/BMS bridge $150-$350; API/cloud license $50-$300 annually or one-time depending on vendor.
Practical Ways To Lower Evolution Connex Control Expenses
Buyers can reduce costs by selecting a model with only the needed I/O, doing preparatory work, and scheduling installs during off-peak months. Simple scope control — limiting the number of zones and avoiding costly wired runs — often cuts the total by 20%-40%.
- Provide clear access and existing wiring to avoid extra labor.
- Choose wireless integrations only when reliable in-site signal exists.
- Compare 3 contractor quotes; request itemized parts vs. labor.
- Consolidate multiple control upgrades into one visit to save mobilization fees.
Regional Price Differences and Typical Turnaround Time
Labor and permit costs vary by region: coastal metro areas are typically 10%-30% higher than Midwest or rural markets. Expect installation time of 1–2 days for a standard residential job and 2–5 days for multi-zone or commercial setups.
Example deltas: Northeast/West Coast +15% to +30%; Midwest/South baseline; rural often -5% to -15% on labor rates.
Common Add-Ons, Fees, and Example Quote Scenarios
Common extras include startup testing, programming, remote access setup, and extended warranty. Typical add-on fees: startup/programming $100-$350, extended warranty $50-$200, rush or after-hours $150-$400.
| Scenario | Specs | Labor Hours | Per-Unit Rates | Total |
|---|---|---|---|---|
| Basic single zone | Controller, 1 relay, 25 ft cable | 2 hrs | Controller $250 | $350-$550 |
| 3-zone residential | Controller + 2 expansion modules, 100 ft wiring | 4-6 hrs | Per zone $200 | $800-$1,300 |
| Commercial 10 zones | Networked panels, gateway, commissioning | 16-40 hrs | Per zone $400-$700 | $4,500-$12,000 |
Questions That Change Quotes When Buying an Evolution Connex Control
When requesting quotes, include panel model, required I/O count, existing wiring, desired integrations (cloud/BMS), and preferred warranty. Providing those specifics upfront avoids large post-quote change orders and gives more accurate low-average-high pricing.